Aaa clicky flashlight5/11/2023 In terms of throw, the i5R EOS measured higher than specs, so that’s again a positive sign. Measurements were taken 30 seconds after turn on, indoors at 5 meters, with a professional Hagner E4-X Lux Meter. Low will run for 35+ hours, and I haven’t tested it. The total runtime with an Eneloop AA is 2 hours. The total runtime with 14500 2.4V is 3 hours and 19 minutes The runtime test was done with the 50cm integrating sphere, including the Kenko Pro1D ND-16 filter and Extech SDL400 data logging Lux Meter. This is pretty common for Olight flashlights. These numbers look pretty good, and are higher than specced. For microamps, I use a cheap DMM with an easy-to-use micro amp setting. For higher amps, I now use a Fluke 325 True RMS clamp meter. The base measurement is done with a Convoy S2+ that has been tested at 255 lumens.įor Amp readings, I use a Fluke 77III DMM. It is set up with an Extech SDL400 Lux Meter for measurements including a Kenko PRO1D ND-16 filter. We will assess the fees involved and will let you know once we receive it.Īll output numbers are relative to my homemade Integrating Sphere. After 5 years of purchase: Return the product to Olight and we will repair or replace it. This does not include obvious user wear or extreme damage. Within 5 years of purchase: Return the product to Olight and we will repair or replace it as long as the light is not working because of factory defects. If your Olight product has any defect as the result of the materials or workmanship we want to make it right! Within 30 days of purchase: Return the product to the retailer you purchased it from and they will replace or repair it. Olight warranty according to their website: The pocket clip has a typical blue Olight coating and can be used in both directions, but it doesn’t appear to be extremely strong. The head has no knurling and is glued to the battery tube. The battery tube doesn’t have the traditional knurling, but 2 parallel lines going around the body. It seems to me that the switch assembly is as heavy as the body+head together. The switch is the only part you can unscrew, and when unscrewed you’ll see copper threading. An AA flashlight with a protruding tail switch, and a 2-way pocket clip. When I first saw its design, it reminded me of the Lumintop EDC AA. The pocket clip also serves as a anti-roll feature, so it won’t roll of the table. The package, however, didn’t include a lanyard, but there’s plenty of them online for relatively cheap. The clip also has a tiny hole, that you can use to attach a lanyard to. It’s attached just below the tailcap, and as the name implies, can either point it upwards or downwards. In terms of carrying, you can use the pre-attached 2-way pocket clip. There’s no way you can tail stand the i5R EOS, just like the i5T EOS, without help, because of the protruding switch. You just have to half-press/tap the switch to change modes. The benefit of a reverse clicky switch is that you can change modes, while the flashlight is still turned on. ![]() It will only turn on when you fully press the switch and after you hear the click. Reverse clicky switches work a different way. If you want to change modes, you basically have to turn the light off, and repeat the half-press until you have the other mode selected. When you fully press the switch, you’ll hear a click, and that mode is set. ![]() When you repeat the half-pressing, you’ll switch between the 2 modes, low and high. It’s a forward-clicky switch, so when you half-press the switch, the light will turn on. There’s only 1 switch, and it’s located at the tail. If you really care about the few millimeters here, and there, take a look at some AAA lights we reviewed, otherwise keep on reading. But when it comes to capacity, an AA battery has about 3 times the capacity of an AAA battery. When comparing AAA and AA flashlights, it’s not too uncommon that they are almost the same length.
0 Comments
Leave a Reply. |